Reasons why the washing machine does not wash well, how to check the water quality
Today, almost every apartment has a special washing machine that is used to wash dirty things. It's bad when such an irreplaceable technique stops working properly and starts washing away dirty spots. When such a problem occurs, it is necessary to understand the reasons why the machine does not wash well.
The main reasons for poor-quality washing
There are eight main reasons that lead to the deterioration of washing quality. It is recommended that you understand each of these causes before troubleshooting the issue.
excess detergent
It's no secret that you need to use special cleaning agents to wash things. Some people who rarely use washing equipment do not know how to properly add powder to it.
This leads to the fact that dirty things cannot be completely washed off, even minor dirt.
When adding a new powder, you must be careful and follow the instructions of the agent used.Most often, information on the use of such formulations can be found on the back of the package. It is very important that the optimal proportions are observed, since the quality of cleaning the linen depends on it. For example, do not add too little powder, as this will prevent the washing of the clothes. An excess of the amount of detergent composition also negatively affects the quality of washing, since whitish spots will remain on the surface of the fabric, which will have to be washed by hand.
Inappropriate remedy
There are many different formulations for washing clothes, and as a result, some people struggle to find the right powder or gel. There are times when the machine fails to wash stains out of dirty clothes due to the use of poor quality and cheap powder. Too cheap products are not able to clean the dirt absorbed from the fabric, and therefore pale spots with streaks may remain on its surface.
Experts recommend checking in advance whether the detergent is the cause of the malfunction of the machine. To do this, it is necessary to thoroughly rinse the tray in which the detergent is poured. Next, new detergent in powder or liquid form is added to the rinsed container. After the washing machine is finished, the washed items are carefully examined and checked for stains. If they are not there, the selected product is suitable for removing stains.
overload things
Sometimes people don't start washing until a lot of unwashed items have accumulated. More often than not, too many clothes are placed in the drum, resulting in poor washing performance.Experts do not recommend overloading washing equipment, as this can cause it to break down over time. Constant overloads cause the drum to malfunction. It can also stop spinning altogether. To eliminate such a malfunction, you will need to seek help from a specialist.
People who have recently purchased a new washer should read the operating instructions. Here you will find information about the maximum amount of laundry that can be placed in the drum in one wash.
Too low pressure in the water supply
The quality of washing may deteriorate due to the fact that the pressure in the water supply is weakened. Therefore, if the laundry has ceased to be washed normally, it is necessary to check the pressure power yourself. Every person can do it. To do this, you need to open the tap, which is responsible for supplying cold water.
If the liquid is flowing slowly, the pressure is really low.
The weakening of the pressure of the liquid supply not only aggravates the washing, but also leads to the appearance of other problems. If the water is delivered too slowly, the internal sensor installed in the washing system may completely stop the washing process. It is difficult to independently establish the cause of the poor water supply, and therefore it is better to call a plumber who will inspect the plumbing system and, if necessary, repair it.
Pump malfunction
A special pump is installed in each washing machine, which is responsible for draining water. If that pump fails or starts to malfunction, the washing machine sometimes washes things worse. There are several reasons why it can be understood that the drain pump has failed:
- The pumping system stops working.It does not turn on even after activating the drainage program.
- Foreign noise. When the washing machine begins to drain water, after operation there is a buzzing sound with tapping and other extraneous noises.
- Slow pumping. If the pump malfunctions, the water is pumped out more slowly.
- Shut down the system. A malfunction is indicated by the fact that the machine turns off when pumping liquid.
Clogged drain filter
At the entrance to the washing equipment, a special mesh filter is installed, which is responsible for filtering the water entering the system. Most often, such a filter element is installed where the inlet pipe is connected, through which water enters the system. Tap water may contain small particles and various impurities, due to which the filter gradually clogs. Due to clogging, the flow of liquid slows down and the quality of laundry deteriorates.
To solve this problem, you need to remove the intake pipe and clean it with the filter. It is best to use a stiff brush and warm water for cleaning. If the blockage is strong enough, you will need to use citric acid, which can eat away even old dirt that has dried on the walls.
bent pipe
Problems with the hose, which is responsible for the fluid supply, also lead to poor washing of dirty clothes. Most often, people are faced with a kink in the hose, due to which water begins to flow further into the washing system. This leads to an increase in the washing time, as well as to the disconnection of the device.
Experts advise periodically to visually inspect the hose and check whether it is pinched or not.If during the inspection a puddle was found, then there are cracks on the hose and it will have to be replaced with a new one. If there is no pinching or damage, and the water still drains slowly, then you will need to start cleaning it from accumulated dirt inside.
Water quality
The quality of tap water entering the machine affects the washing process. For example, if the liquid comes into contact with rust when it enters the washing machine, then yellowish stains with spots will appear on the surface of the washed clothes, therefore, before you start washing, you need to check the liquid quality. If rusty water often flows from the tap, you will need to install additional filters with purification systems.
Also, washing equipment may wash clothes worse due to high water hardness. If the water is too hard, it means that powdered detergents dissolve less well and therefore it is difficult to remove stains from the surface of the fabric. In such cases, softeners are used, which are added before washing.
How to check water quality
Before washing, you should check the quality of tap water in advance. The easiest way to do this is to boil. For this, a clean pan is prepared in advance, which is half filled with liquid. Then the container with water is placed on a gas stove and boiled for ten minutes. When the liquid boils, pay special attention to the walls of the pan, as well as its bottom. If the water is of poor quality and contains many foreign microelements, scale deposits will appear in the pot.
General rules for washing and choosing a machine mode
Before you wash your laundry, you should understand the general washing rules:
- Sort things out. All garments are recommended to be sorted in advance by color and material of manufacture. It is best to wash woolen, cotton, synthetic and linen items separately.
- Checkered pockets. Clothing pockets are checked in advance for foreign items.
- Loading the drum. It is loaded so that it is not overloaded and can rotate normally.
- Dosage of detergents. For the laundry to wash well, it is necessary to respect the dosage of the powder.
Additional tips and tricks
There are several recommendations you should read before washing your clothes:
- things should not be washed in too hot water, as they can deteriorate;
- do not add a lot of powder, because there will be spots;
- in order to choose a suitable way of washing, it is necessary to preliminarily inspect the labels on the clothes;
- powder should not be added to the drum as it will settle on the fabric.
Conclusion
Owners of washing machines are often faced with the fact that they begin to remove dirt more and more. It is recommended to familiarize yourself with the causes of this problem and know how to get rid of it in advance.