Technical characteristics of the Ceresit CT 17 primer and consumption rate per m2

Priming is an important step in renovation work. With the help of this procedure, it is possible to significantly improve the characteristics of the treated surfaces and increase their service life. To achieve the desired results, it is important to choose the right composition. Many craftsmen prefer Ceresit ST 17 primer, which has the best technical characteristics.

Composition and technical characteristics of the Ceresit CT 17 primer

Ceresit ST 17 soil is a universal water-dispersing substance. Its characteristic is considered a light yellow tint of the film. After drying, a characteristic shine appears on the surface. This makes the base easily recognizable even after complete polymerization. Also, the composition contains additional components - alkyd and ebonite resins, polymers, drying oil.

Due to the variety of components in the composition of the Ceresit floor, it provides a complex effect. The main properties of the substance are as follows:

• Deep penetration ability. Thanks to this, the floor contributes to the qualitative strengthening of the treated base and turns into a component that binds particles of dust and dirt.
• Reduced absorption properties of the coating. For this reason, using a primer can reduce the need for staining by 1 square meter.
• No impact on the vapor permeability of the coatings.
• Suitable for use on heated screeds.
• Various forms of release. There are formulations for winter and summer on sale.
• Increased lifespan of wallpaper and tile adhesives.
• Possibility of applying plaster in a thin and uniform layer. The cracks linked to the drying out do not subsequently appear on the surface.

The composition is considered environmentally friendly. The instructions state that the primer is suitable for indoor and outdoor use.

The technical characteristics of the material are shown in the table:

Advantages and disadvantages of the material

Soil has certain advantages and disadvantages. The main advantages of the material are:

• The ability to quickly and deeply penetrate the surface of the treatment area.
• High drying speed.
• Reinforcement of the upper layer of the plane.
• Lack of harmful components.Therefore, the primer can be used for the repair of residential premises, kindergartens and medical institutions.
• The presence of antiseptic ingredients in the composition.Thanks to this, the material prevents the growth of fungi.
• Ease of application.
• No need for special storage conditions.
• High concentration of the mixture. Undiluted, the composition takes up little space. When mixed with water, the required concentration is obtained.
• Availablity.

At the same time, Ceresit CT 17 has the following disadvantages:

• Yellow color after drying. It is not always possible to fully cover this color. This is especially difficult to do with the subsequent use of white finishing materials.
• The need for precise application of the primer. Dirty surfaces are difficult to wash off the primer. Therefore, before using it, additional planes must be covered.
• Specific smell. After drying, it disappears.

Groundbait has far fewer disadvantages than advantages. Therefore, many craftsmen choose this substance for repair work.

Certificate of conformity

This material has many advantages, therefore it is considered very popular. At the same time, it is very important to purchase a quality primer with the appropriate certificates.

Look at Also

What kind of substance is a pigment, its description and properties in the composition of dyes

Packing and Release Form

The tool is a deep penetrating water-dispersion primer.

Color pallet

After drying, the primer forms a light yellow film on the surface.

Purpose and properties

The material is suitable for surface treatment before using plaster and flooring compounds or tile adhesives. The substance can be used for the treatment of any absorbent coating.

These include:

• concrete;
• cement-sand plaster;
• cement-sand screed;
• masonry;
• lime plaster and gypsum;
• particleboard and fibreboard.

Primer Ceresit CT 17 has the following characteristics:

• contains only environmentally friendly ingredients;
• can be used for external and internal work;
• thanks to the yellow tint, it makes it possible to identify the treated areas and the missing places;
• can be used to strengthen the foundation without violating the parameters of vapor permeability of the surface;
• helps to achieve deep penetration;
• does not harm the human body and does not pose a threat to the environment;
• is not affected by temperature fluctuations, so it can be used to treat walls behind batteries and underfloor heating;
• has different types - the assortment of the brand includes soil that is not afraid of frost.

Advantages and Disadvantages of Requesting Seed Jobs

Using a primer has many advantages. These include in particular the following:

• Good penetration capacity in the coating on which the material is applied.
• High concentration of the product. As a result, the material takes up minimal storage space.
• Maximum surface hardening. The primer contributes to a significant increase in adhesion parameters.
• Fast drying.
• No harm to health. Thanks to this, the material can be used in children's and medical institutions.
• No specific requirements for storage conditions.
• Reliable protection against fungal and mold infections.

Due to the absence of toxic components in the composition, the primer can be used in different rooms. It does not harm the health of children, therefore it is often used in kindergartens and schools. Also, the composition is suitable for hospitals and other medical institutions.

In this case, the primer also has some disadvantages. Some people who have used the substance have noted its high cost. But this minus is individual.

Another conditional defect is considered a yellow tint. This allows you to identify unpainted areas, but sometimes causes difficulties when painting. Most often, problems arise when using white materials for decoration.

Also, the disadvantage of the primer is the complexity of its removal.If the mixture is poured on a surface, it can be difficult to clean. However, this drawback can hardly be called significant. With careful use of the material, the risk of these problems occurring is low. If the primer is used on linoleum, then it is worth protecting the surface from the penetration of the substance by covering it with a film.

In general, the advantages of a primer far outweigh the disadvantages. When using this material, it is possible to significantly improve the properties of the treated surface.

How to calculate material consumption

The recommended amount of soil per 1m2 is 150 milliliters. However, for old and porous surfaces, the dosage can be increased. In this case, 200 milliliters of substance are needed per m2. In the construction of online stores, there are often special online calculators that facilitate the process of calculating the required amount of the composition.

Look at Also

Types and areas of application of fire-retardant paints for wood, the best brands

Tools needed for work

For preparatory work, it is necessary to prepare a putty composition, which is necessary for sealing seams and cracks. To protect windows, doors and baseboards from the primer, you need to use masking tape.For the use of the substance, it is recommended to prepare the following tools:

• brush;
• roll;
• construction mixer - it can be replaced with a clean wooden stick;
• paint palette;
• a bucket of clean water.

Rules for surface preparation and working solution

Ceresit CT 17 primer can be used for the treatment of walls. This composition makes it possible to strengthen them. If the old coating is not firmly attached, it must be removed. It is recommended to tap the walls beforehand. This will help detect loose areas of the cast, which then need to be removed. If large cracks or depressions appear, they should be rubbed with putty.

At the stage of preparing surfaces for applying the primer, it is recommended to do the following:

• Remove any visible traces of plaster, cement or other materials.
• Remove all types of coatings. Exceptions are water-based and acrylic dyes.
• Dry the walls thoroughly. After using the plaster, it will take at least 2 weeks, after applying putty - 1 day.
• To avoid contamination of areas that do not need to be treated with soil, it is worth sticking paper tape in these places.
• Get rid of mildew, oil stains and other blemishes.

Before using the primer, shake it sufficiently. It is recommended to thaw the winter solution in a warm room. Mix well before use. In this case, the composition does not need to be diluted.

Ceresit CT 17 Deep Penetration Primer Technique

When using a primer, you must strictly follow the instructions. Apply by roller, brush or brush. For highly absorbent substrates and anhydrite floors, it is recommended to apply the primer in 2 working passes.In this case, in the first case, it is necessary to apply a primer mixed in equal parts with water.

It is recommended to carry out further finishing work only after the primer mixture has completely dried. It takes an average of 4 to 6 hours. The specific time is determined by the drying conditions.

Immediately after the end of the work, it is recommended to rinse the tools with plenty of water. After drying, the primer can only be removed with a solvent.

It is important to take into account that it is recommended to carry out all work in dry conditions. In this case, the air and base temperature indicators should be + 5-35 degrees. Relative humidity should not exceed 80%.

It should be borne in mind that the floor slightly changes the shade of the treated base, causing its slight yellowing. This helps distinguish treated areas from untreated areas.

Drying time

The primer dries on average in 4-6 hours. In this case, the specific duration depends on a number of factors, the main of which is the temperature. The warmer it is in the room, the faster the coating dries.

Look at Also

Technical characteristics and composition of the XC-059 primer, rules of application

Possible errors

When using the material, many novice craftsmen make a number of mistakes, which negatively affect the quality of the coating:

• do not prepare the surface for the primer;
• temperature and humidity parameters are neglected;
• do not respect the drying time of the coats.

Security measures

Despite the relatively safe composition, the use of Ceresit CT 17 primer requires taking precautions. It is important to use personal protective equipment when applying the product. For this, it is recommended to use protective glasses, gloves, a mask or a respirator.This will help prevent the negative effects of the composition on the human body.

Also, when using a primer mixture, it is important to take into account that it is very difficult to wash off. Therefore, surfaces that are not intended to be primed should be covered. Windows, doors, baseboards should be sealed with adhesive tape.

Cost and storage conditions

The cost of a container with a volume of 10 liters is 600-700 rubles. Store the primer in a cool, dry place. This is best done on pallets. The composition should be kept in its original packaging and ensure that it is not damaged. It is important to protect the substance from freezing.

Recommendations from the masters

When using the Ceresit CT 17 primer mixture, it is important to adhere to the recommendations of experienced craftsmen. This will help you get the desired results. So, when applying a primer, consider the following:

• It is necessary to store and work with the composition at a positive temperature. In this case, the parameters should be + 5-35 degrees. Humidity should not exceed 80%. Otherwise, the soil does not dry out. Any remaining moisture in the mixture will cause bubbles to form. The only exception is the special winter composition Ceresit ST 17. After freezing, the substance can be used. In this case, you need to thaw it gradually. To do this, it is enough to place the substance in a warm room.
• When applying the primer, it is important to avoid puddles on horizontal surfaces. In this case, the streaks should not appear on the walls. The primer can be applied manually or using special devices. In the first case, a roller or brush is used, in the second - a compressor.
• After applying a coat of primer, it must be completely dried before continuing work. It takes 4-6 hours. If the primer is applied to porous surfaces, it must be dried within 24 hours.
• The quality of the layer can be evaluated experimentally. To do this, an adhesive composition or a dye in the form of a small grain can be applied to the dried surface and the dynamics of its drying can be assessed. If the material dries unevenly and this process is accompanied by the formation of light spots, it is recommended to apply another layer of primer. Materials with large pores must be treated twice with the product. Also, when applying the first coat, the primer should be diluted by half with water.
• After drying and polymerization, the material acquires the properties of chemically inert materials and becomes insoluble. Therefore, it is recommended to rinse the tool with water after completion of work.

The use of Ceresit CT 17 primer allows to reduce the consumption of finishing materials, improve the quality of the coating and increase its service life. That is why this material is so popular.