Atlant washing machine decoding errors and how to fix the problem
Of all the problems that arise with the Atlant washing machine, error F4 occurs more often than others. This code is highlighted on the screen when no water is entering or the built-in motor fails. You can fix this error yourself. The appearance of other codes usually signals the need for specialized and often expensive repairs.
Identification of faults by code
Atlant cars are equipped with a display that shows the selected operating mode, the remaining time and the error code. These are of the following types:
- Nothing;
- Door;
- F2 to F15.
The appearance of one of these codes does not always indicate a malfunction. Knowing what a specific error means can help you narrow down the problem finding.A specific code indicates a failure of a specific part. However, this only indicates problems with this element, although the malfunction may be hidden in other parts of the machine.
Nothing
This signal indicates that due to the large amount of foam, the drum cannot rotate. If None appears frequently, it is recommended to replace the current detergent with another one, or to choose suitable operating modes.
Door
Door indicates that the mower door will not close. This problem is caused by:
- door lock breakage;
- damaged wiring feeding the central board;
- violation of contacts;
- incorrect installation of the washing machine;
- a defect in the guide or retainer;
- misalignment of hinges.
Some of these defects can be eliminated on your own. Other problems will require specialized equipment to help assess the condition of the wiring.
F2
The F2 code indicates a failure of the temperature sensor, which occurs due to a violation of the integrity of the contacts (wiring) or a failure of the control unit.
F3
This error appears when the electronics of the washing machine detects a malfunction of the heating element. Heating element failure is caused by scale buildup or a broken contact.
F4
F4 appears if water drainage is disturbed (water flows slowly or stagnates in the tank). Basically, this code appears when the pipes are clogged or the pump fails.
F5
This signal indicates a blockage in the water supply pipe. Also, the F5 error occurs if the intake valve breaks.
F6
F6 appears on the washing machine display if the reversing relay fails. Also, this error occurs in cases where the motor is faulty or the contacts are damaged.
F7
F7 indicates insufficient voltage in the mains or a broken noise filter. In this case, it is impossible to restore the operability of the machine without the intervention of a master.
F8
The F8 error occurs if:
- the water inlet valve is blocked;
- the pressure switch is broken;
- the control board is faulty.
Due to each of these failures, water remains in the tank of the machine.
F9
F9 indicates a faulty sensor that measures engine speed.This malfunction also occurs due to a broken contact or broken wiring.
F10
F10 occurs in cases where the contacts or the electronic system responsible for blocking the door are faulty.
F12
This error appears when there is a problem with the motor or the control unit (triac on the central board).
F13
This code appears when the control board is faulty or the power contacts are damaged.
Such breakdowns occur due to a short circuit caused by the ingress of moisture.
F14
The appearance of this code indicates a software malfunction. The malfunction is eliminated by rearranging the software.
F15
This code indicates the presence of leaks inside the Atlant machine.
Methods to solve certain situations
Most of the errors that appear on the display of the Atlant machine are eliminated only with the help of specialized equipment. But in some cases, you can restore the effectiveness of the equipment yourself.
F3
The F3 error occurs if:
- the heating element has failed;
- scale has built up on the heating element;
- the control module is faulty;
- The heating element is incorrectly connected.
The troubleshooting procedure is the same in each case.
grilled water heater
If you suspect a heater element failure, you should:
- remove the rear cover of the washing machine;
- remove the terminals;
- unscrew the bolt in the center of the rod;
- loosen the heating element with a screwdriver and remove it from the socket.
It is impossible to independently determine the breakdown of the heating element. Therefore, if it is suspected that the heating element has burned out, the part should be replaced. The new water heater is inserted as shown in the diagram, but in reverse order.
Scale buildup on parts
Scale on the heating element is considered to be the main reason for the failure of the heating element. To clean the part, you will need specialist descalers.
Control module failure
Depending on the type of Atlant washing machine model, the control module is located directly on the heating element (on new equipment) or next to it. This part is removed together with the heating element according to the diagram above. In case of failure, the control module is replaced with a new one.
Bad device connection
This malfunction occurs in cases where the heating element has been replaced. To fix the problem, you need to reconnect the contacts.
Form 4
The F4 error is considered the most common, since this code occurs due to a blockage in the water drain system. This problem is eliminated without the intervention of third-party assistants.
The drain filter is clogged with foreign bodies
The drain filter is located at the bottom of the washing machine. To clean this part, simply unscrew the cap counter-clockwise and rinse.
Sewer Blockage
To identify this problem, simply remove the drain hose from the hose and activate the spin mode on the machine. If the water is drained and F4 does not appear on the screen, this indicates a blockage in the sewer.
Bent drain hose
Due to the crease, the water in the machine stagnates. To fix the problem, just straighten the pipe.
Engine rotor wedge
Threads, toothpicks, or other similar items can get into the engine during washing and stop the engine. To eliminate this malfunction, you will need to disassemble the machine and clean the Atlanta parts.
Drain pump failure
The drain pump fails for the following reasons:
- the motor coil is cut;
- a short circuit has occurred (dark traces are visible);
- the wheel is defective;
- the lifetime has expired;
- small objects touched.
In each of the above cases, you will need to replace the drain pump.
Clogged drain pipe
Small objects often enter the drainpipe, interfering with the flow of water. To clear the F4 error, you need to clean the clogged parts.
Lack of power contacts
You can identify this malfunction with the help of an external inspection of the wiring. In addition, it is recommended to check the condition of the wiring with appropriate equipment.
F5
The F5 error occurs if there is no water in the tank.
Clogged filter screens
These strainers are located on the drain hose and filter. These parts are constantly in contact with water, which can contain both small and large particles.
To remove the blockage, simply clean the threads.
Lack of water in the plumbing
If an F5 error occurs, it is recommended to open the tap and check the cold water before dismantling the machine.
Intake valve breakage
The deformation of the valve is due to frequent interruptions of the water supply. Failure of the solenoid coil winding or core is also possible. This problem can be solved by replacing the valve.
There are no contacts on the valve or solenoid module
If this problem is suspected, it is recommended to disconnect the terminals and strip the contacts. The defective electronic module must be returned to the master for repair.
The pressure switch does not generate an "empty tank" signal
The main reason for this malfunction is a blockage of the hose going from the tank to the pressure switch. The fault can be eliminated by purging this element.
F9
The F9 error code indicates a malfunction in the tachometer sensors that count engine speed. Such a problem arises due to the breakdown of these parts or the failure of electronics.
Tachometer damage
The tachometer is located in the motor and consists of two elements: a fixed coil and a magnet. To check the first, you need a multimeter that analyzes the resistance level.
Defective coil
The defective coil must be replaced. To identify a breakdown, it is necessary to check the resistance level - first with the engine stationary (the indicator should be equal to 150-200 kOhm), then turn the shaft by hand. In this case, the indications should change.
Incorrect engine speed
This malfunction mainly occurs due to frequent overloading of laundry or power surges. Both factors cause the motor windings to short, requiring the failed motor to be replaced with a new one.
F12
The appearance of F12 on the display indicates a malfunction of the drum drive motor.
Bad contact on wiring block
This malfunction is revealed by a visual inspection of the wiring. To repair the motor, you will need to remove the terminals and strip the contacts. It is recommended to lay the wiring in such a way that the cables do not come into contact with other parts during operation of the machine.
Broken windings
This problem occurs when the drum is constantly overloaded. A break in the windings is evidenced by the increasing noise that occurs when the washing machine is running. This malfunction is eliminated by replacing the defective parts.
Brush wear
Due to the design features of Atlant washing machines, the brushes constantly rub, which leads to abrasion of parts. These elements must be replaced with new ones. During the procedure, it is recommended to check the condition of other engine components and clean the contacts.
Triac malfunction
The triac, which controls motor speed, fails due to power surges or motor failure. This part is also subject to replacement.
Rules of operation of the washing machine
Some parts of the washing machine, due to natural reasons, fail over time and need to be replaced. To avoid more serious problems such as engine or electronics failure, it is recommended not to overload the drum and periodically clean the drain pipes, pumps and pumps. If the washing machine is installed in a house where the electricity is often cut off, the equipment must be connected to a device that smooths out voltage surges (surge protector and the like).