Reasons why the washing machine may not fill with water and do repairs yourself
Owners of washing machines are often faced with the fact that the washing machine does not fill the system with water. Many people do not know what to do to solve this problem. Therefore, it is recommended to familiarize yourself in advance with the reasons for the interruption of the water supply and the main methods of repairing the washing machine.
Reasons for the absence of a water set
There are eight reasons why a washing machine stops pumping water.
Valve closed
Often the equipment does not receive water due to the valve being closed. Many inattentive people who forget to open the tap for normal liquid supply to the washing system are faced with such a banal problem. There are different situations in which you need to close the valve. Most often this is done before carrying out repairs related to the water supply.Also, some people turn off the faucet for safety reasons, to avoid water leakage.
Therefore, before you start washing, you need to make sure that the tap is in the correct position.
Blockage in inlet hose or filter
Another common problem that prevents water from flowing through the washer is a clogged hose. The problem begins to manifest itself in the summer, when repair work on the water supply begins and the water supply is turned off.
It is after the resumption of the water supply through the pipes that rust and debris appear, which quickly clog the inlet pipe.
If the water does not flow well, you should disconnect the hose and check it. If there is any debris inside, you will need to start cleaning it. To do this, clean the walls of the pipe with a thread and rinse it with water.
Defective machine valves
The liquid enters the washing system using special valves, which differ in a simple principle of operation. In order for water to enter inside, voltage is applied to the valve. After that, it opens and closes after a power failure. Sometimes the valves stop responding even after connecting the machine to the power grid. This happens due to short circuits in the system or power surges.
Damaged wiring
If the washing machine hums too much and does not draw water at the same time, the wiring is damaged. There are two reasons that lead to malfunctions in the wiring:
- Pulling wires. Manufacturers sometimes stretch wires too much, which shortens their lifespan. Due to the increased tension, some of them begin to break.
- Use fine threads.Sometimes the wiring in the washer consists of thin elements that stop working properly when there is a voltage drop.
The above problems lead to the fact that the valves are not powered and water does not enter the drum.
Control module failure
Each modern washing machine is equipped with an electronic module, which is a mini-computer, consisting of RAM and a central processor. The module monitors the operation of the equipment when washing dirty clothes. The rupture of this part can manifest itself in different ways. Sometimes the machine does not turn on at all, but sometimes it happens that due to a malfunction in the module, the water stops pumping.
Malfunction of the pressure switch
Modern washing machines independently determine the amount of water in the tank. A special device is responsible for this - a pressure switch. Over time, it begins to work less well and transmits incorrect data to the control board. A faulty pressure switch cannot determine whether the tank is full or empty. The mower will not fill with water until the part is working properly.
Therefore, you will have to restore the pressure switch or replace it with a new one.
The hatch is not closed tightly
A banal reason for the lack of water is an improperly closed tank of the washing machine. Sometimes it is difficult to tell if the appliance door is completely closed. If it is ajar, the machine will not be able to start the process of filling the tank with water. Therefore, you need to make sure in advance that the hatch is tightly closed with a latch.
Drain pump in a cliff
If the washer is not sucking up liquid, you need to check the drain pump.It seems to many that the drain has nothing to do with pouring water, but it does not. If the technician is having trouble draining the old fluid, they will not fill the reservoir with new water. Therefore, you need to disassemble the machine and make sure that there is no breakage in the drain pump. If it fails, you will have to buy a new pump and replace the old one.
What to do
There are several recommendations that will help normalize the operation of the washing machine and restore the flow of water.
Checking the water tap
If the liquid is not supplied, it is necessary to check the tap, which is responsible for the outflow of water. When checking, you must make sure that it is installed in the correct position. Sometimes people turn off the water on their own and forget to turn it on.
If during the check a broken valve was found, you will need to replace it with a new one and then check whether the machine will pump water into the tank.
Drain the water, check the hose
Sometimes the water does not flow out due to the fact that there is a little liquid left in the system of the machine, which must be eliminated. To drain the water, do the following:
- disconnect the hose that connects the washer to the sewer;
- put it in an empty bowl or bucket.
After draining the water, you can check the inlet hose and clean it if there is a lot of debris inside. If you can't clean it properly, you can replace the hose with a new one.
We clean the filter of the washing machine
A filter is installed in the inlet pipe, which cleans the water of debris particles. Over time, it becomes clogged, which leads to deterioration in the outflow of fluid. When inspecting the filter, it is best to use a flashlight to better see how dirty it is.If there's a lot of debris on it, you'll need to remove it, clean it with a brush, and put it back in place.
To prevent the filter from getting too dirty, it should be cleaned once a month.
Contact a service center or specialist
People unfamiliar with repairing washers should not attempt to repair them themselves. Especially when it comes to expensive models from Samsung, Intezit or LG. It is better to entrust such work to professionals who have been repairing washing machines for more than a year. You can contact an individual master or use the services of special service centers.
Independent solution
People who decide to repair the washer themselves should familiarize themselves with the repair recommendations.
If there is a problem with the valve
When the water does not flow due to damage to the valve hose, you need to start replacing it. To access the broken part, you must disassemble the top cover of the machine. Then the branch pipe is carefully unscrewed so as not to damage the fasteners. Before installing a new part, all joints are carefully greased with glue for a secure connection. Bonding areas are sealed with mastic to prevent water leakage.
If the heating element is faulty
A malfunction of the heating element leads to the fact that water ceases to accumulate in the drum. To check the performance of the heating element, you need to disconnect the washer from the electricity and check the part with a multimeter. If an open or short circuit has been detected, you will need to replace the heating element with a new one.It is better to entrust the replacement to professionals who know how to repair washing machines.
Lock
If the water does not fill due to a broken door lock, you will need to replace the lock with a new one. This is hard work best left to a specialist.
Conclusion
Some washing machine owners have difficulty filling the wash tub. If the water does not come, you need to find out the causes of such a problem and find out how to fix it.