How and with what to glue a frame pool at home
For the manufacture of inflatable and frame pools, polyvinyl chloride film is used, which has a high density. The multi-layered material maintains the shape of the product well. However, any mechanical damage leads to leakage. The situation is aggravated by the lack of funds for plugging the holes. How to glue a puncture in a pool frame in the absence of professional skills, we will understand further.
Preparation for repair work
First you need to make sure there is a puncture, as a drop in the water level may be due to natural evaporation. Pour water into a basin or bucket. Now place the container in the pool. Use a marker to mark the liquid level on the bucket and pool side. Compare the amount of water in the containers after 24 hours.
The leak could be caused by a broken drain valve or a damaged hose. Fluid begins to seep through the filter gasket. To determine the location and nature of the defect, you can use special dyes.In this way, the direction of movement of the tinted liquid is determined.
If the problem is with the drain valve, the gasket should be replaced. Pay attention to the bottom of the pool. Debris begins to accumulate near the puncture. If the pool is made of PVC, cyanoacryl-based glue should not be used.
The reason for this is that when the composition dries, a hard seam is formed. During operation, the cyanocryl begins to crack. This leads to a violation of the tightness of the product.
How to glue inflatable models correctly
The method of repair depends on the degree of damage to the product. If the puncture is on the outside, air bubbles will appear on the surface of the water.
Method 1: Use a repair kit
To seal the hole in the pool, you can use a ready-made repair kit. The set consists of a special glue and a patch. Drain the pool to repair the damage. Then cut out the PVC patch. The damaged area should be degreased with an alcohol solution. Now apply a thin layer of glue and apply a patch to the sting. The seal can be compromised by the penetration of air bubbles. Therefore, you need to put the load on the glued area.
Method 2: tape or plaster
Damage to the inflatable structure can occur from being cut with sharp objects. In intensive use, the seams do not withstand the load. How to seal a puncture in a frame pool if there is no repair kit at the dacha?
If you don't have waterproof glue, use materials on hand. Tape or plaster will work to fix the puncture. Degrease the damaged area before carrying out repair work.The downside of this method is that the commit is unreliable.
In high humidity conditions, the adhesive tape quickly peels off the surface. This method of repairing a leak is considered a temporary measure. To seal small cracks, a faucet sealant is used to fill the cracks.
Method 3: vinyl glue
You can get rid of large flaws with vinyl glue. Eliminate air bubbles during work. Otherwise, it will be impossible to exert firm pressure on the edges of the patch. Also, polyvinyl chloride cannot be sanded with sandpaper. Using an abrasive material will only extend the area of damage.
To repair pools, use low-viscosity products ("Alteko", "Vinyl Cement"). Manufacturers produce special compounds that quickly restore tightness. The drying time of the sealed area under the press is 12-24 hours.
Important! It takes several days for the waterproof adhesive to harden completely. Therefore, do not immediately pour water into the bowl.
Method 4: vulcanization
There is a possibility of solving the problem by cold vulcanization. The inflatable device is repaired at the seams, which are considered the most vulnerable point of the product. The slightest damage leads to a leak.
The vulcanization of the product is carried out in a car service. The preparatory work includes the following operations:
- surface cleaning;
- treatment of materials with a degreasing solution;
- dry the puncture area.
How to properly repair frame models at home
There are several ways to restore the tightness of the product.
Method 1: adhesive tape
First you need to identify the puncture site.The damaged area is indicated by a marker. After that, the surface must be cleaned of dirt. Use an alcohol solution to degrease the material. Apply a patch to the puncture area. Adhesive tapes are only used for temporary sealing. After the end of the season, further renovation is required.
Method 2: repair kit
To fix leaks in frame pools, you will need to use a repair kit. Also, the pool owner cannot drain the water. To eliminate the defect, it is worth using an underwater patch. It is installed on both sides of the damaged area. When choosing an adhesive, you should pay attention to the components. The product should not contain toxins that will have a negative effect on human health. A prerequisite is moisture resistance. After the composition dries, an elastic seam should form.
Features of work with certain models
The choice of the method of restoring the seal depends on the builder of the swimming pool.
Best way
First you need to find the puncture site. You can use a sealer to repair minor cracks. If the diameter of the hole exceeds 1mm, a patch should be used. Before carrying out any work, you need to clean the material from dirt with a soft brush. After that, the surface is degreased. Particular attention should be paid to seams subject to high stress. It is necessary to put a load on the sealed area in order to increase the reliability of fastening.
Patches should be cut in a circle or oval shape. The presence of corners will lead to chipping of the material due to the constant movement of water flows. There should be no air bubbles in the connection area. The drying time of the adhesive under the press is 12-24 hours. The pool owner can use bitumen roofing tape, which will restore the seal. Waterproof sealants are used to fill small holes. Their composition is resistant to ultraviolet rays and does not lose its qualities in conditions of high humidity. To seal the seams, you can use an industrial hair dryer, which reliably glues both sides of the gap.
Intex
To repair your Intex swimming pool, use the dedicated repair kit. The composition contains moisture-resistant VinilCement glue, protective gloves, a set of vinyl patches and a sealant. VinilCement contains polyurethane, acetone and chlorinated hydrocarbons. The product released by Intex is very effective. Apply glue to the patch using a stick. Now you need to firmly press the piece of PVC onto the damaged area. To speed up drying, the patch is heated with a hair dryer.
The pool owner will need to purchase the VinilCement glue separately from the main product. It is not a cheap pleasure. To save money, you can use other waterproof products. For example, you can use Moment glue. The quality of the repair depends on the nature of the puncture and professional experience.
During repair work, you must observe the following sequence:
- First empty the bowl and wait for all surfaces to dry.
- For minor damage, a sealant is used that completely fills cracks and cracks.
- Vinyl patches are used to remove large defects. Their size should be 2 cm larger than the damaged area on each side. To achieve a tighter connection, a weight should be used.
Rules of maintenance and operation
The inflatable or frame pool must be on a flat surface. Sharp stones and metal objects can damage the PVC. To reduce the risk of accidental tearing, place a mat or foam underneath.
While swimming, you should not sit on the sides of the bowl. Failure to do so will result in material deformation and damage. After the end of the summer season, clean the surfaces from dirt. Thoroughly dry the inflatable pool. It is recommended to store the folded product in a warm room.